And here's easy way to Install the Nitrous System.
NOS Kit Number 5151
This is a very quick and basic article on how to
install the NOS kit 5151, for the TPI equipped Camaro, Firebird, and
Corvette. The information here is taken directly from the installation
manual provided by NOS. Of course the manual is more detailed, but
the point of this article is to give a brief explanation of
installation procedures. A full installation manual can be purchased
separately from NOS for $5.00. The manual is included with the setup.
Step 1: Mounting the Bottle
NOS recommends mounting the bottle in the well,
in the hatch area, by using the supplied brackets. Because of the open
compartment in the 3rd generation F-Bodies a safety blow-down tube is
used. The bottle should be turned approximately 45 degrees so the
label is facing towards the front of the car. This will place the
pickup tube near the back of the bottle where the an ample amount of
nitrous will be during acceleration. The bottle brackets need to be
screwed down to the floor of the well to prevent the bottle from moving
around during acceleration. Two holes will need to be drilled in the
floor. One of these holes is for the safety blow-down tube and the
other is for the nitrous feed line.
Step 2: Injector Plate Mounting
First remove throttle linkage and throttle body.
Then install plate and gaskets onto the upper plenum with the spray
bar orifices facing into the upper plenum. Then reinstall the throttle
body and linkage with the extended bolts and throttle linkage.
Simple.
Step 3: Fuel feed lines
**For safety disconnect the negative terminal of the battery**
Locate the schrader valve on the fuel rail. Remove protective black
cap and decore the schrader valve using a tire valve core tool.
Step 4: Fuel and Nitrous solenoids
Place the nitrous solenoid in a padded vice and
install the supplied nitrous filter into the inlet side of the solenoid
using Teflon tape. Next, install the supplied 2-ft. braided line with
the blue fittings, to the outlet side of the solenoid using Teflon
tape.. Now place the Fuel solenoid in the vice and install the 2-ft.
Piece of braided line that has red fittings to the inlet side of the
solenoid (of course using Teflon tape). Then install the other 2-ft.
Piece of braided line, with the r ed fittings, to the outlet side of the
solenoid. (Don't forget the Teflon tape or you will have a very
Hazardous Leak!!) Next, mount the fuel and nitrous solenoids to the
solenoid mounting bracket. Now mount the bracket in a place where the
fuel feed line will be able to reach the solenoid and at the same time
be able to reach the injector plate. As shown in the picture, the
bracket was mounted to the strut tower. Connect the fuel feed line to
the schrader valve, and connect the remaining lines to the injector
plate. **Note - All N.P.T. fittings must be sealed with Teflon Tape!**
Step 5: Nitrous feed line routing.
This is a simple step, but needs a lot of
attention. Basically connect the supplied braided line to the valve on
the bottle and to the Nitrous solenoid. Routing the line under the car
needs to be done properly. Make sure the line isn't near any moving
parts. If this line gets broken while the bottle valve is opened, a
full bottle will empty in approximately 1 minute. ** Note - before
connecting line to the Nitrous solenoid, It is a good idea to purge the
bottle once to release any condensation that may have gathered inside.
Basically to do this just open the bottle for a few seconds.**
Step 6: Throttle Micro-Switch Installation
The micro-switch is mounted to the throttle
bracket. This switch is what actually activates the solenoids.
Therefore proper installation is essential. Adjust the switch so that
at wide open throttle the switch is depressed. For proper accuracy,
have a friend sit in the car and floor the accelerator pedal. At full
throttle you should here a quiet click. This means the switch has been
activated. Make adjustments so that the switch is activated only at
full throttle. This will ensure the computer is in an open-loop and
the fuel mixture is adequate.
Step 7: Wiring of the system.
This step is probably the hardest, but can still
be done by you. See picture for exploded view of system. The system
is simple in that you have two switches to activate for the system to
be operative. The first switch is mounted in the car and activated
first. This switch should be on whenever you are ready to hit the
throttle. The first switch supplies the power to the throttle switch.
Then, when the throttle is fully opened, the throttle switch activates
the solenoids to open and release fuel and nitrous into the system.
The system has its own power and ground, and the actual power to the
solenoids is run through a supplied relay.
Step 8: Preparing for operation
Reconnect the negative terminal on the battery
and turn ignition on. Check for leaks at this time at all fuel
connections. Then open valve on the bottle. Check for leaks at all
nitrous connections. Temporarily disconnect the ground wire from the
Nitrous solenoid. Activate the switch mounted inside the car. Start
engine and have a friend rev to 2500 RPM. Manually depress throttle
switch for a second or two, to open Fuel solenoid. At this time you
should notice a bog in the engine. This means the electrical system is
functioning properly. Reconnect ground wire to Nitrous solenoid. Find
yourself an open street and LET IT RIP!!!
Conclusion:
NOS system 5151 have adjustable Jets to properly
set your horsepower levels. NOS recommends 100 horsepower for a 305 and
up to 150 horsepower for a 350. NOS states that the stock fuel pump is
adequate for these levels of horsepower and the stock timing does not
need to be adjusted. This is a very thorough kit that comes complete
with everything you will need for proper installation.
Personal additions:
There are a few parts I recommend installing
along with this kit. For proper operation of the nitrous system the
nitrous pressure must be approximately 900 psi. With the temperature
constantly changing it is a good idea to install a Nitrous Pressure
gauge. This will put you in control of how much pressure is actually
getting to the solenoid. Personally, I would recommend an Auto Meter
Nitrous Pressure gauge. I would also recommend installing an Auto Meter
electric Fuel Pressure gauge. This will allow you to keep an eye on
fuel pressure for proper tuning. I do not feel that stock fuel
pressure settings are adequate. It is better to be safe than sorry so I
bumped up my fuel pressure by 2 psi. These gauges can be easily
installed by using the NOS gauge adaptors. If you are using an
aftermarket CHIP for your car then an adjustable timing retard may also
be a good idea. Most aftermarket chips have a really aggressive
timing curve and NOS does not recommend that their kit be used in
conjunction with one of these chips. Since it seems that one of the
first mods that everyone does is a CHIP, then an adjustable timing
retard such as the one MSD offers is a perfect compliment to the
nitrous system. The timing retard can be wired up in such a way that
when the nitrous system is activated the timing retard is activated.
Then as RPM's increase, timing decreases.
Have Fun!
No comments:
Post a Comment